Zigbee Wireless Technology Trainer Model Manufacturer,Supplier and Exporter in India
.png)
Product Code : SCL-CE-12645
Zigbee Wireless Technology Trainer Model (Product ID: 12645) is part of the Communication Equipment range under our Laboratory equipment catalog, and is a rack-mounted trainer built around embedded 89C668 controller nodes that teaches Zigbee wireless mesh networking, addressing and self-healing routing.
Note on naming and scope: our catalog also carries the closely related Bluetooth Wireless Technology Trainer (Product ID: 12644), which uses the same rack-mounted, replaceable-NIC experiment platform but is specified for Bluetooth instead of Zigbee. The Network Interface Card section of this product still refers to a "Bluetooth application module", while the rest of the technical specification (frequency band, range, data rate, addressing) is for Zigbee. Please confirm with our team which wireless module ships with this unit before ordering.
Quick Answer
The Zigbee Wireless Technology Trainer Model is a table-top, Aluminum-profile rack setup built to teach Zigbee wireless protocol fundamentals, including self-routing, self-healing, fault-tolerant mesh networking with a large number of available network addresses per channel. Four embedded nodes, each with a replaceable NIC, let students configure master/slave roles, exchange data between devices and observe transmission status on-board.
Key Features
Comprehensive experiment set-up explaining Zigbee wireless protocol fundamentals · Choice of shared set-up with replaceable NICs, or independent node set-up, with NICs swappable between technologies · Table-top setup built on a light but sturdy Aluminum profile (4x2) rack · Self-routing, self-healing and fault-tolerant mesh networking · Point-to-point, point-to-multipoint and peer-to-peer topologies supported · Over 65,000 unique network addresses available on each direct-sequence channel · RSSI indication on LED · 4 embedded nodes with 4 replaceable NICs kept under a transparent cover
Experiments / Topics
Software configuration of Master and Slave devices · Data exchange from one device to another · Selecting a device name and transmit key, with LED status messages observed on-board
Key Specifications
| RF Specification | |
|---|---|
| Operating Frequency Band | ISM 2.4 GHz |
| Indoor / Urban Range | Up to 133 ft (figure given as 400 m in source – see note below) |
| Outdoor Line-of-Sight Range | Up to 400 ft (approx. 120 m) |
| Transmit Power | 2 mW (3 dBm) |
| Receiver Sensitivity | 95 dBm RF (see note below) |
| Data Rate | 250,000 bps |
| TX Current | 40 mA @ 3.3 V |
| RX Current | 40 mA @ 3.3 V |
| Node Hardware (per node) | |
| Embedded Controller | 89C668 operating at 16 MHz; on-chip RAM 8 KB; Flash/EEPROM 64 KB |
| Serial Port | RS232C, 9-pin D (M) |
| USB Interface | Built-in USB to serial converter |
| Display | 20 x 4 LED (Backlit) |
| Indicators / Switches | General purpose SMD bicolor (green, red) 8x2 LEDs and 8 SMD push button / DIP switches |
| Power | 5 V / 2.5 A SMPS with RCA plug; AC input 230 Vac ±10%, 50 Hz × 4 Nos. |
| Software | |
| Node Software | Embedded program written in C for Bluetooth & Zigbee protocol |
| PC Software | Network Monitor |
| Mechanical | |
| Dimensions / Weight | 900 mm (L) x 300 mm (W) x 720 mm (H), approx. 20 kg |
Note: please confirm two figures with our team before ordering: (1) receiver sensitivity is listed as "95 dBm RF", while receiver sensitivity is normally a negative dBm value; (2) the indoor/urban range is listed as "up to 133 ft" with "400 m" in brackets, although 133 ft is about 40 m. The outdoor range (400 ft / 120 m) is consistent.
Scope of Supply
Table-top Aluminum profile (4x2) rack trainer set-up with 4 embedded 89C668-based nodes, 4 replaceable NICs under a transparent cover, RS232C serial ports with built-in USB-to-serial converters, 20x4 LED display per node, power supplies, and Network Monitor PC software. A lab PC with a serial or USB port is required for network monitoring but is not included in the scope of supply.
Where This Is Used
This trainer is used in wireless communication labs to teach Zigbee mesh networking, addressing and topology concepts, and is relevant to institutions equipping Electronics Lab Equipment and Engineering Lab Equipment facilities.
Frequently Asked Questions
What does the Zigbee Wireless Technology Trainer Model teach?
It teaches Zigbee wireless mesh networking concepts including self-routing, self-healing and fault-tolerant mesh operation, point-to-point/multipoint/peer-to-peer topologies, and master/slave device configuration across 4 embedded nodes.
How many nodes and network addresses does the system support?
The trainer includes 4 embedded nodes with 4 replaceable NICs, and per the manufacturer's specification each direct-sequence channel offers over 65,000 unique network addresses.
Is there a related Bluetooth version of this trainer?
Yes, we also list a Bluetooth Wireless Technology Trainer (Product ID: 12644) built on the same rack-mounted, replaceable-NIC platform but specified for the Bluetooth protocol; please check with our team on module details before ordering.
Related Categories
Laboratory · Electronics Lab Equipment · Engineering Lab Equipment
Request a Quote
For pricing, bulk quantities or tender documentation on the Zigbee Wireless Technology Trainer Model, reach our team via Contact Us or submit your requirement through our Tenders page.
.png)
.jpg)
.png)
.png)